750 mm Wheat Beige Vanity - One-Piece Ceramic Top-Basin

A narrow ceramic-top vanity where the basin and the top are one fired piece: no silicone joint to re-seal, no resin ledge to yellow, and a carcass specified for a bathroom that runs at 80 percent relative humidity.

A 750 mm vanity is what fits when the bathroom wall is short and the shower tray is already there, and it is the size a Brazilian distributor sells most of in the entry and mid segment. The catch is that most 750 mm units pair a cheap ceramic top with a board carcass that has no business in a wet room. CB750 pairs a one-piece vitreous china top-basin fired at 1,150 C with an 18 mm E1 moisture-resistant carcass, 1 mm ABS edges on every exposed face, and DTC soft-close hinges. It flat-packs in two cartons, 0.133 m3, 508 pieces per 40HQ - a container of one SKU at a defensible cost per piece.

  • ModelFAME-CB-750WT (CB750 series)
  • Overall size750 W x 460 D x 820 H mm, wall hung, 31 kg net
  • Carcass18 mm E1 moisture-resistant board to EN 717-2, melamine faced both sides, sealed back edge
  • Fronts / finish18 mm E1 board, wheat beige super-matte melamine at 4 gloss units, slab profile, 3 mm shadow gap
  • Edging1 mm ABS on all exposed edges, hot-melt glued and trimmed, PVC-free on request
  • Top-basinOne-piece vitreous china, 1,150 C fired, white glaze, 25 mm rim, overflow with chrome cover

Trade inquiry only — this is a B2B catalog with no online checkout. Our team replies within 24 hours.

Full Specification

  • ModelFAME-CB-750WT (CB750 series)
  • Overall size750 W x 460 D x 820 H mm, wall hung, 31 kg net
  • Carcass18 mm E1 moisture-resistant board to EN 717-2, melamine faced both sides, sealed back edge
  • Fronts / finish18 mm E1 board, wheat beige super-matte melamine at 4 gloss units, slab profile, 3 mm shadow gap
  • Edging1 mm ABS on all exposed edges, hot-melt glued and trimmed, PVC-free on request
  • Top-basinOne-piece vitreous china, 1,150 C fired, white glaze, 25 mm rim, overflow with chrome cover
  • BowlIntegrated single bowl, 420 x 300 x 130 mm internal depth, 12 degree fall to a 45 mm waste
  • Tap drillingSingle 35 mm centre hole as standard; 3-hole 35 mm on 200 mm centres quoted as a separate SKU
  • Doors / hinges2 x 375 mm doors, DTC soft-close, 110 degree, 3-way adjustment, 50,000-cycle rated
  • InteriorOne adjustable 5 mm glass shelf, anodized pins at 32 mm pitch, no fixed shelf so a trap can pass through
  • MountingGalvanized steel hanging bracket with +/- 5 mm levelling, template and 4 anchors in carton 1
  • Packaging2 cartons per piece: carcass 790 x 480 x 180 mm 5-layer; china top 800 x 510 x 160 mm with moulded cavities and 15 mm foam
  • Volume / weight0.133 m3 per piece combined, 34 kg gross (31 kg net), 3.1 kg per 0.01 m3
  • Loading / MOQ508 pcs per 40HQ at 68 m3 usable, 205 pcs per 20GP; MOQ 20 pcs per model, 3 finishes mixable from 60 pcs; 25-30 days after deposit and finish approval
  • Port / termsFOB Ningbo or Shanghai; CIF Santos and Paranagua quoted on request, with AFRMM shown separately on the freight line

Why Buyers Choose This Model

  • 750 W x 460 D x 820 H mm wall-hung, 31 kg net - a short-wall size that sits beside a 600 mm shower tray without a site cut, and 460 mm deep so it clears a 700 mm door swing
  • One-piece vitreous china top-basin fired at 1,150 C with a 25 mm rim and a single 35 mm tap hole - no joint line between top and bowl, which is the joint that grows mould first on a two-piece unit
  • 18 mm E1 moisture-resistant board (EN 717-2 chamber method) with melamine on both faces and a sealed back edge, specified for a bathroom that sits at 80 percent RH instead of a dry showroom
  • 1 mm ABS edging hot-melt glued and radiused on every exposed edge - a 0.4 mm tape edge lifts inside two seasons in a steam-heavy room and takes the board with it
  • Two 375 mm doors on DTC soft-close hinges, 110 degree opening, 3-way adjustment, 50,000-cycle rated, with one adjustable 5 mm glass shelf on anodized pins at 32 mm pitch
  • Two cartons per piece, 0.133 m3 combined - carcass in one, fired top in a separate moulded-cavity carton so nothing presses on the glaze in the container
  • 508 pieces per 40HQ at 68 m3 usable and 205 per 20GP - 12.8 kg per 0.1 m3, so the container fills on cube, never on payload
  • Faucet, waste and trap are quoted as separate lines at 1,200 pcs per 40HQ equivalent, so a distributor can land a complete bathroom set on one entry file instead of three suppliers

Specification Questions Buyers Ask

Why specify a one-piece ceramic top instead of a ceramic top with a separate bowl?
Because the failure mode of a two-piece unit is the joint, not the china. A silicone line between top and bowl moves with thermal cycling, collects soap and hard-water scale, and is the first place a customer photographs for a warranty claim. A single fired piece has no joint to re-seal on site, and the glaze covers the whole visible surface, so there is no unglazed rim to stain. The trade-off is that a break in transit takes the whole top, which is why the china ships in its own moulded-cavity carton rather than in the carcass carton.
Is 18 mm E1 board acceptable for a Brazilian bathroom, or does it have to be marine ply?
E1 is the emission class, not the moisture class, and the two get confused in RFQs. What the bathroom needs is a moisture-resistant board grade, sealed edges and mechanical protection at the cut edges - and that is what this carcass specifies, with melamine on both faces and 1 mm ABS on every exposed edge. Marine plywood is a different product for a different budget; if a specifier names it, quote it as an alternative, but do not accept 'E1' on its own as evidence of humidity performance.
What does the tap hole drilling have to be on the drawing?
A single 35 mm centre hole covers most single-lever mixers sold in Brazil and is the standard here. If the program sells a three-hole mixer, the top has to be drilled 35 mm on 200 mm centres at the factory - it cannot be drilled on site without chipping the glaze, and a locally drilled top voids the glaze warranty. Put the drilling on the approved drawing and check the first production piece against it, because this is a mould change, not a machining change.
How many pieces actually fit, and does the china limit the load?
It fills on cube, not weight. At 0.133 m3 per piece and 34 kg gross, 508 pieces is 67.6 m3 and about 17.3 tonnes - well inside a 40HQ payload that runs above 26 tonnes, so nothing is weight-limited. The constraint to plan for is stacking: the china cartons carry no load on the glaze face, they travel at the door end, and the carcass cartons go behind them. Ask for the loading photo set with the shipping documents.
What spare parts should be in the first container?
Two percent of hinges, one spare door front per twenty pieces, one spare top per hundred if the distributor has no local china supplier, and a bag of hinge plates and shelf pins. Hinges and tops are the two parts that generate a consumer complaint; a door front is the part that arrives damaged. Ask for the parts as a separate line on the invoice so they are not treated as samples at entry, and land them with the first container rather than the second - the legal warranty clock in Brazil starts at retail sale, not at shipment.

Building a Basins Program?

Send your target market, sizes and quantities — we reply within 24 hours with a tailored quotation.

Start Your Inquiry